tan the fisherman Posted July 24, 2009 Share Posted July 24, 2009 (edited) Hi Raiders, As an Alvey reel doesnt oscillate, is there a special way to spool it with line. Im trying to get my blackie reel ready. Thanks Tan Edited July 24, 2009 by tan the fisherman Link to comment Share on other sites More sharing options...
hottyscotty Posted July 24, 2009 Share Posted July 24, 2009 not really, just run the line between your fingers and move it left to right. dip line in water so it won't burn your fingers. you want it tight on the spool otherwise you'll get birds nest on first cast Link to comment Share on other sites More sharing options...
jewgaffer Posted July 24, 2009 Share Posted July 24, 2009 (edited) Tan it's a good idea to spool a few metres of mono onto your reel and then drop the rod tip down near the floor and if the mono line has curls thru it, try reversing the spooling direction {i.e. the direction the line comes off the spool} from anti clockwise to clockwise... Cheers jewgaffer Edited July 24, 2009 by jewgaffer Link to comment Share on other sites More sharing options...
humkyle Posted July 24, 2009 Share Posted July 24, 2009 definatly make sure it goes on tight.... it comes off how it goes on.. i learnt that the hard way. HK Link to comment Share on other sites More sharing options...
tan the fisherman Posted July 24, 2009 Author Share Posted July 24, 2009 it going on but all in one spot - im trying to move it slightly left and right but I dont think its on right - hate to get out there and it all f@cks up on me - I bought some top notch line Link to comment Share on other sites More sharing options...
hottyscotty Posted July 24, 2009 Share Posted July 24, 2009 how badly in one spot? like one big lump in the middle? then you'll need to redo it Link to comment Share on other sites More sharing options...
tan the fisherman Posted July 24, 2009 Author Share Posted July 24, 2009 (edited) how badly in one spot? like one big lump in the middle? then you'll need to redo it nah its smooth just filling up about 1.5cms from backing plate side forward Edited July 24, 2009 by tan the fisherman Link to comment Share on other sites More sharing options...
hottyscotty Posted July 24, 2009 Share Posted July 24, 2009 should be ok. aslong its flat and in small angle is ok. just make sure its tight, its the loose coils that will give you grief Link to comment Share on other sites More sharing options...
Trapper Tom Posted July 25, 2009 Share Posted July 25, 2009 G'Day Tan When ever I load up a reel with new line (not braid) I chuck the shop spool into a bucket of water. I then load from there. If there is any twists etc then the spool in the water keeps revolving around and lessens the eventual twists that might end up on your loaded reel. With a alvey you should be OK even putting it on directly as, as you have said, there is no oscillation, its a straight line transfer. Even so the benefit of the bucket of water is that:- 1. As you wind the line on, use thumb and first finger to hold the line, water on the line = does not burn your fingers. 2. Thumb and first finger work back and forwards to load the line evenly on the reel. 3. Keep medium pressure on the line when loading with your thumb and first finger so that it beds. Note too much pressure is just as bad as to little pressure. To much can actually affect the reels shape and squash it, to little and yes the birds nest. 4. The water over the whole length of line going on to the reel helps bed the same. Hope the above helps. Don't know quite why I don't do the above with braid. I have this probably outdated and dinosaur thought that it is a fabric type of product and if loaded wet will shrink when it dries (fully loaded) and affect the reel. I know this does not make sense, as you get a big run from a fish that strips stacks of line off, the braid dries on the reel and I have had no probs here. You also rinse reel etc on return from a trip. Its a question that's been in the back of my mind for a while now so has any FR a answer to the above, would love to know!!! Cheers Trapper T Link to comment Share on other sites More sharing options...
tan the fisherman Posted July 25, 2009 Author Share Posted July 25, 2009 G'Day Tan When ever I load up a reel with new line (not braid) I chuck the shop spool into a bucket of water. I then load from there. If there is any twists etc then the spool in the water keeps revolving around and lessens the eventual twists that might end up on your loaded reel. With a alvey you should be OK even putting it on directly as, as you have said, there is no oscillation, its a straight line transfer. Even so the benefit of the bucket of water is that:- 1. As you wind the line on, use thumb and first finger to hold the line, water on the line = does not burn your fingers. 2. Thumb and first finger work back and forwards to load the line evenly on the reel. 3. Keep medium pressure on the line when loading with your thumb and first finger so that it beds. Note too much pressure is just as bad as to little pressure. To much can actually affect the reels shape and squash it, to little and yes the birds nest. 4. The water over the whole length of line going on to the reel helps bed the same. Hope the above helps. Don't know quite why I don't do the above with braid. I have this probably outdated and dinosaur thought that it is a fabric type of product and if loaded wet will shrink when it dries (fully loaded) and affect the reel. I know this does not make sense, as you get a big run from a fish that strips stacks of line off, the braid dries on the reel and I have had no probs here. You also rinse reel etc on return from a trip. Its a question that's been in the back of my mind for a while now so has any FR a answer to the above, would love to know!!! Cheers Trapper T Thanks Tom - I have decided on the sure fire, tried and tested way to spool this reel. Im taking it back to the shop and the bloke can do it for me. He was very busy at the time and couldnt do it. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now