darynxbcoupe
-
Posts
44 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Fishing Tips, Advice and Articles
Blogs
Store
Everything posted by darynxbcoupe
-
I have had the boat back on the water a couple times, last time conditions were very flat and only had 50 litres of fuel on board. Just my mate and I and still could only get 28 knots. The boat doesn't take any water in the hull from rain and hull is a dry hull
-
Fuel is always fresh as I use it all the time
-
Going to have to check these points, the hull is very clean so maybe plugs
-
The speed is coming through the GPS
-
-
Hi All, I have a f115A coming up 2 years old now with 150 hours on it, when I first bought my boat the top speed was around 31-33 knots, now I only seem to be getting 27-29 knots. I am running the same prop. Does this sound like something wrong with the engine?
-
I have a Formosa 580 in the tomahawk range, the trailer has rollers. Best trailer I have had. I heard from the dealer that the " classic" range needs to be skid as they are not high tensile alloy as the " tomahawk " range is high tensile alloy and can go on rollers
-
It is all very tight, I think I might need to ask the supplier
-
This is a new prop, never hit anything as its only got around 20 hours on it.
-
Hi All, I have a solas SS prop Rubex NS3 on my FA 115 Yamaha, when I first put it into gear at low rpm it vibrates quite bad...when I put a bit more throttle down it is sweet. Has anyone had this with a propeller before? Cheers daryn
-
I have just played with Simrad and thankyou as It has gone, easy when you know how... thanks again Jewfish
-
Okay, I wouldn't have thought about that..Thanks
-
Thanks heaps Jewfish for your help, I will plug in unit and give it a go. My mate told me to do the same thing and get a cable to learn inside rather than on the water. Thanks Daryn
-
Thanks for that,
-
Hi All, I have a Nss9 Evo 2, I got a structure scan transducer fitted and since then I get tracks really thick as wide as an inch... I have been told the bellow answer, I cant seem to work out how to fix this, any help would be much appreciated Hi Daryn u have structure over on in chatting option, turn this off and it will disappear. Cheers Daryn
-
Thanks for your advise I will lower it and test after work this week, much appreciated.
-
So should it be totally under the hull then?
-
thanks for that, it isn't behind a strake, here is a couple photos Any suggestions?
-
will get picture tomorrow, what is the strake??
-
Hi all, I have a Simrad nss9 with a HDI 50-200 transducer, I cant seem to get it set correct as it has too much interference and only works properly at around 3 knots. Will it work better if I put it as far away from motor possible?? I have about 100mm I could move it on the plate. Cheers Daryn
-
Hi All, has anyone had any experience with Yamaha GYT Performance 3 blade props? Thanks
-
Thanks Huey, I didn't realise I needed that one.
-
Hi All, I have recently bought a NSS9 unit with a 50-200, 455-800 transducer. I cant seem to get the structure scan to work, all it shows is a dark grey screen with the depth etc, but no bottom readings. has anyone got one of these units that may be able to help? Thanks Daryn
-
Thanks all good now, just have to get on water
-
Thanks for that, I know have detailed contour lines. I am having trouble trying to transfer waypoints from my card to the unit? I have downloaded Garmin Home Port and the marks are on my card but cant get them to display on my unit? Any suggestions? Cheers Daryn
