[Port Stephens- Big Day, Big Gear, Big Result]

Hi all...well done fellas,must have been a big day and a lot of Klm .

ill see you up there tomorrow baz.

[Port Stephens- Rack em up!!!]

Hi all...well done fellas,i was going to go up yesterday myself.

[What would you buy for 45k?]

Hi all...anthman,I selling my barcrusher 610 c soon with all the fruit for $45 k ono.

[Port Stephens- plan A-B-C]

Hi all...well done scratchie and woodsy.i going up tomorrow,hope I snag a good one myself.

[Researching a new spot]

Hi all...you can also use navionics and use your phone as a gps to get to the spot then mark your sounder/gps.

[what is the name of this on the outboard motor?]

Hi all...petcock valve.

[Rust spots]

Hi all...them rust spots look like grinding sparks to me.some ones been grinding steel close to your boat.

[Last keel roller on Trailer]

Hi all...why not pack up either side of roller with rhs and put some of that red plastic on the packers .

[Last keel roller on Trailer]

Hi all...what about a roller either side of the problem roller ?

[Broughton Snapper]

Hi all...scratchie,we done much the same as you,with a nice 65cm one in the mix.

[Broughton Snapper]

Hi all...well done fellas,i was up there today myself.

[What is this bar on my new boat???]

Hi all...if you going to take them off,i would mig weld the holes,oxy welding will put to much heat into the alloy and distort the alloy,migs alot cooler.if you put them back on i would sikaflex them back on.

[Fishing Port Stephens]

Hi all...a few months ago i seen agood snapper caught off little beach jetty.it was about 55-60 cm.

[cmap vs navionics]

Hi all...ive got both.navionics is heaps better.

[It Comes in Threes, Right?]

Hi all…good to catch up yesterday baz

[Transducer installation help]

Hi all...fishmore,i got trim tabs on my boat,and yes,you need to move your transducer over.

[Broke down on hacking last night]

Hi all...your last post wasnt there when i replied last LOL.

use your mouth to blow rather than compressed air.

[Broke down on hacking last night]

Hi all...did you blow thru the fuel line to check the float level ?

[Transducer installation help]

Hi all...fish more,i bought a cover from my local boat shop today.it only cost a couple of dollars.still needed to use a good blob of sikaflex.i feel your better off making a plate with a slotted hole,you would use less sikaflex.

i could mail you one up if you wish.

your boat looks the same brand as mine.

[Broke down on hacking last night]

Hi all...once you have checked your float level ect,check to see if your slow jets not blocked,it gives similar symptoms.

[Transducer installation help]

Hi all...fish more,ill be getting stuck into mine tomorrow.i was going to use my old cover,but since you have pointed it out,mine will be to small also.i think the local boat shop would be my first look for one,there the ones who usually fit out the electronics in boats.ill let you know when i get there.

[Transducer installation help]

Hi all...fish more,im installing a new sounder and transducer as well.use a cable cover and a suitable silicon.

[It Comes in Threes, Right?]

Hi all...yes,that was me scratchie.there were a few boats up there,which was you ?

im not to sure i buy the argument that wd40 degades rubber,well not engine rubbers anyway.diff seals prop seals ect ect are in an oil based environment.im sure all engines would have rubbers suited to oil environments.i do agree wd40 is a good degreaser.the grease around my linkages seems to hang on.wd ,inox ect are better than nothing.

[It Comes in Threes, Right?]

Hi all...ive had a tps go on one of my motorbikes,also a mate had the same problem.

Baz,i lather under the hood of my boat engine with wd40 every 2nd trip.i buy 5liters of wd40 and use a spray bottle to apply the wd40,i give a good drenching.

I was up broughton on friday myself,was my worst day fishing in years.

 

[Boat Fuel Discussion - What Do You Use and Why?]

Hi all...btw,i keep my fuel tank topped up full always.my boat rides better with weight.