[port macquarie blackfish and yabbies?]

thanks everyone for your help, sorry its been late getting back to you all. ive been flat out for the last few days.. ill post some pics if I do any good .

thanks again.stephen..

[port macquarie blackfish and yabbies?]

hello all, as the title suggests I need help with some directions for fishing port..

I am taking the family up late next week and bringing my tinny with us. im looking for somewhere to pump some yabbies' in the river and a landbased blackfish spot around the entrance to the river..

any help would be greatly appreciated. thanks in advance..Stephen..

[Bonito on the BBQ]

yep soy sauce and sweet chilly= awesome

[Wind forecasts?]

I also use windfinder and willy weather together

[Advice on Mid North Coast NSW holiday with kids]

there is a place at port mac. edgewater holiday park. its not too bad..

[Bream Tactic]

try fishing in shallower water. about 1-2m deep up on the sand/ weed beds..

[TARGETING TUNA TROLLING LURES]

what is that ice you are using???

home made?

[New Leader Working]

I just use 6lb Schneider off the rocks. cheap and does the job no problems.. if the knot breaks it only my fault.lol

[Removing a seat from the tinny?]

plus it already has those ribs in it next to the seat so I think it should be ok..my boat has two bench seats with ribs in the middle and it hasn't collapsed it on its self yet..

[Removing a seat from the tinny?]

in an old fishing book I have they cut away the middle seat and had some wide trays/ reinforcing placed down the side of the boat..

[Where are the Bonnie's?]

heaps around terrigal mate, we got 17 2 weeks ago..

[swell around sydney tomorrow]

windfinder. has the swell at just over 1m for tomorrow. today was about as flat as it gets off terrigal..

[Outboard won't run full throttle unde load]

so did the engine rev really high even though you were only at walking pace????

[Knife sharpeners]

I take mine to my local butcher, only costs $5 per knife

[Outboard won't run full throttle unde load]

I had the same sort of problem with my 15hp Yamaha. it turned out to be the propeller bush. which is a rubber grommet type thing that holds the prop onto the shaft. a new prop did the trick.. got mine from solas.

hope this helps..

[Building a false floor for savage snipe tinnie]

any photos??

[PB Common Skate]

wow, great catch mate.. thanks for sharing..

[Further protection for galvanized trailer]

fish oil is the go. just talk to your local smash repairs..

[Central coast fishing]

will you be fishing in the ocean or inside Brisbane waters??

[Boat Perspex Replacement]

that rubber should be fine. but prob check with a windscreen fitter first.. you will still have to seal the rubber after you lock it together..

be aware that there are different sized rubbers for thicker and thiner glass/Perspex and fiberglass..

ie bigger and smaller openings and the main point is to check the spacing in between the glass and fiberglass panel..

[Hottest Hawkesbury Bite in Years]

thanks for sharing, sounds like a top few days..

[light spin]

look at the fin nor affinity and pflluger trion

[Myna birds]

With a home made trap, you do your own termination on the birds.

that's right..put on some gloves and stretch the neck..

[Myna birds]

I made one of the traps last year and made a fair dent their population, with about 25 birds gone..

the best catch was 4 birds at once..

[Erina Creek Wed 6th. First EP. Bream on hardbodys]

well done, the best fishing ive had is from the woodport inn up..

if you can fish unweighted plastics around there you should get a few nice bream(people feed them chips from the pub)..