seasponge Posted January 15, 2018 Share Posted January 15, 2018 I'm finally getting around to installing my Lowrance fish finder that's been gathering dust in my bedroom for way too long. I have an old aluminium hull with a ribbed profile. I was going to mount the transducer about 300mm to the right of the prop, in between two of the ribs. Am I likely to get interference from the proximity of the ribs? (not that there's any alternate location I can put it in). Also, the hull has a decent deadrise, so anticipating having to play around with the height of the transducer initially to get it reading correctly, would it be recommended to mount to a transom mounting plate, or just screw the brackets direct to the transom? (There is slight adjustment available in the slotted holes in the bracket). This is my first fish finder installation so any other tips would be helpful. Link to comment Share on other sites More sharing options...
Fab1 Posted January 15, 2018 Share Posted January 15, 2018 Sikaflex a board to the transom and mount your transducer to that in-between the planning strakes.Remember to screw the transducer screws into the centre of the slotted transducer mount so you have final adjustment up/down.If it's a new sounder you will have mounting instructions.Is that an old Quinny Hull? Link to comment Share on other sites More sharing options...
seasponge Posted January 15, 2018 Author Share Posted January 15, 2018 Yeah i was thinking of mounting a board first. It's a new sounder but instructions just say to keep it a certain distance from the prop, and away from any planing strakes. It's an old Stacer. Link to comment Share on other sites More sharing options...
rickmarlin62 Posted January 15, 2018 Share Posted January 15, 2018 if you have an 83/200 or 50/200 transducer they have a line down the side of them..this should be mounted level with the bottom of the hull..ge someone to hold a ruler or level as a straight edge and mount the transducer parallel with this...my 83/200 reads at 25 knots on my vsea....hds5 luv em..rick Link to comment Share on other sites More sharing options...
frankS Posted January 15, 2018 Share Posted January 15, 2018 Where you intend to place it is the best place and good advise above, the down stroke of the prop is the right side so with what you intend to do is all OK, You will get a certain amount of interference but it cant be helped unless you plate the hull. Frank Link to comment Share on other sites More sharing options...
seasponge Posted January 15, 2018 Author Share Posted January 15, 2018 42 minutes ago, rickmarlin62 said: if you have an 83/200 or 50/200 transducer they have a line down the side of them..this should be mounted level with the bottom of the hull..ge someone to hold a ruler or level as a straight edge and mount the transducer parallel with this...my 83/200 reads at 25 knots on my vsea....hds5 luv em..rick Not as easy when the deadrise is so steep. I'm assuming the transducer needs to be parallel to the ground. Given the slope across the hull, to position the transducer level with bottom of the boat, once side of the transducer is going to be a bit deeper, or shallower than the boat, if you can picture what i mean. Hence why I'm anticipating having to play around with the height once its installed to fine tune the readings Link to comment Share on other sites More sharing options...
rickmarlin62 Posted January 15, 2018 Share Posted January 15, 2018 that's not a steep deadrise..themiddle of transducer should be level with middle of hull between strakes..i wasn't clear enough before sorry..tranny should be parallel with hull not ground..rick Link to comment Share on other sites More sharing options...
rickmarlin62 Posted January 15, 2018 Share Posted January 15, 2018 (edited) Sorry bout rotation Edited January 15, 2018 by rickmarlin62 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now