brickman

no problem ian we always have a few sets rigged up give me a ring on 0438264377 to arange a time for pickup through the week at silverwater weekends at wahroonga cheers gary

simda i got your adapters made today and i'll rigup your poles tomorrow night i've been working on a brakedown for the last few days pulling 14 hour shifts should finish it by monday night hope the fin are still around next week cheer gary

no problem bob and robbie give me a call the night before pickup ph 0438264377 cheers gary

no problem trung i hope to hit the fin early next week cheers gary

they chatter and the rainbow one is for trung hahahahahaha

hey raiders i just got a shipment off bird teasers in 5 and 7 inch we will be rigging these up in line for a flock off bird teaser still have to do the numbers but for 5 x 5 inch birds on 2 meters off 375lb mono 2 meters long will be around $40.00 5 x 7inch birds in line on 375lb mono 2 meters long will be around $50.00 we will sell birds as single units on request and rigg them any way you like just in time for the fin cheers gary

our out rigger setup on a hard top extreme boat at 2014 sydney boat show our poles

raiders we're here to help with any advice on mounting positions on your boat or mods you may need for tee tops cheers gary

a big thank you to donna and stewy for all the help in getting this web site sorted out and up and running and to all the raiders that have purchased products from me in the past just a little info;;;we source all the products directly from the makers no middle man involved that way raiders get the best price any questions just send me a pm or phone any time on 0438264377 cheers gary

mmmmmmmm thats a tricky one i would first get the bait board to the hight and position you really like then get a section folded in aluminium or stainless and mount it inside the wash well but as prev.said tilt the donk up and check for clearance a neat section folded like a channel with tappered ends will hide the fastning points and look flash and when the bait board is removed you have two more rod holders for trolling i have two straight rod holders with backing plates all they need is to be polished you can have them for free the section you need to get folded will have to be done by a sheet metal workshop in stainless 3mm would be fine aluminium proberly 5mm ps marine grade aluminium and 316 stainless or powder coated or two pack paint after etch priming also to help the sheety make a full size template in card board so he gets the angle right hope this helps cheers gary

make the inlet 20 mm short off the bottom of your hull and use a peace off heavey duty air hose with a 45 degree angle cut at the bottom fix the hose to your inlet pipe and face the 45 forward.this will stop damage when hitting floatys cheers gary

very sorry for your loss to steel a boat like this with the locks on you would think they needed a tilt tray tow truck were there drag marks from the trailer wheels now i know it's the polices job but its hard to drive on sydney roads nowdays with out being caught on camera a runaround to all the local shops in your area might shed some light on the bandit you only need a rego plate number proberly a long shot but worth a try cheers gary

my old man sprayed his with fish oil now it looks like crap but it has not rusted cheers gary

only 55 i would have picked you to be much older hahahahahaa have a great day stewy cheers gary

as a general rule 6 inch rsj or ub will hold 1 tonne this is an underestimate check to see if its an rsj [rolled steel joice] the fanges will be tappered or a ub [universal beam]the flanges will be flat this is very important as the trolly will either have to have tappered wheels or flat wheels.most support ub's are between 250 and 400 more than you will ever need unless your going to pick up a truck the bigger question is whats holding up the beams proberly brick colums now this could be a consern with a swinging load over 1 tonne as the beams are proberly just sitting on the brick cheers gary

congrats mate it's about time well done cheers gary

if you could email the pics to seriouslystain@optusnet.com.au that would be great cheers gary

hey raiders i need a few pics off boats that have our outriggers installed on them they will be used on our new web site a side on view would be great getting the whole boat in and a seperate pic off the mounting possition this would be a great help as we need as many pics off boats as possible cheers gary

congrats on the dolly on fly stewy sound like a good weekend cheers gary.ps the new web site will be done in the next few weeks wooohooo

well done lads what a rush your well and truly hooked now lucky pete was up because trung would have cryed like a girl hahahahahaha just a little info for you lads the info i gave you the night before was supplyed from mr magoo [game fishing god ] and erroll above you will quickly find that there is a group off game fishermen that share info on and off the water with radio calls and phone calls i would strongly advise you get to know this group as there intel is gold and if you share they will to thats what i love about fishraider we love fishing but also love getting people on to fish cheers gary

mmmm very interesting with the hook possy thanks for sharing cheers gary

kmart or any good tackle shop bloodworms are also a great bait there are plenty off whiting were you pump nippers that would be inside the beach on the sand flats pump the nipper near the walk bridge on the edge off the creek move around till you find a good patch you should get two nippers per hole even pump in the water just look for two small holes good luck cheers gary

if you going to bundeena take a yabby pump get some nippers and then fish were you pumped them at high tide cheers gary

if your trolling in the next few months use wire trace about two feet long there are reports off spanyards in close and the wahoo will be on the cards also for marlin you need 6 feet off 150 lb mono leader min i use 400lb mono leader for marlin cheers gary

unless there straight up and down the hole needs to be oval shaped drill a hole with a hole saw the o.d. off your rod holder and then using a bur make the hole oval a easy way to do this is make a template off the under side off the rod holder do a little at a time now the important part prime and paint the area or salt will get under the paint and bubble it up to be honest why would you use a plastic rod holder there are good cast stainless and aluminium rod holders out there for around 40.00if your ever going to run a down rigger plastic will not handle it and stainless or aluminium will need a backing plate good luck cheers gary